New Mods this year??

[SS-ROB]

Ok guys what plans do you have for your car this year??

[jrp]

installing an 02 clutch setup in a few weeks, then possibly a custom FMS cam or i'll install my T1 i got sitting in my room.

or if worse comes to worse a new 347 short block with custom FMS cam and TEA heads.

[gauSSian]

in the near future, I have an aux. tranny cooler and deep pan on the way. and that will complete my performance mods for a year or two.

I will begin looking at some appearance mods, but nothing major.

In a few years, I plan a major overhaul of body and engine. I'm thinkin' LPE 427 TT. :drive:

[BradL]

Headers, brake rotors and pads, lowering it, ls6 intake, throttle body and then head/cam package

[BradL]

Oh yeah but first is a decent stereo system

[262 77]

I also need to replace clutch. I have been looking at some h/c packages, just having some thoughts. :)

[02CamaroZ28]

ASP pulley, port TB and MAF, new catback with QTEC, save 2k for my rearend fund when it blows, wheels and tires, and a big cam.

Mark

[Corp Z]

No mods for this season. At least none that I'm planning.

I have a few things that need repair and/or fixing before I put any money into mods. Rear pinion seal, Accessory belt, and sagging rear bumper cover need to be sorted out.

[Hilton]

chassis and suspension shit.
oh and
plugs, wires, fuel filter

[BowlingSS]

SFC's and a TC.. Also would like a GMMG exhaust.

BowlingSS
:2guns:

[SS-ROB]

My plans are to finish out susp. work and a 12 bolt.

[ULTIMTEORANGESS]

converter and cooler waiting to go and 17' nittos or BFGs.

[DVST8OR]

Already on there way, should be here by Monday :D

ASP Underdrive pulley

http://www.lgmotorsports.com/images/asp-pulleykit-ls1.gif


LGMotorsports Panhard rod

http://www.ls1camaro.net/freehosting/g2-panhard-rods.jpg


Raptor shift light

http://www.raptorperformance.com/Red_Slvr.JPG

[Black02SS]

I think for the most part I am done. I installed a new FMS cam and finally got around to getting the ASP pulley. Now I am a full bolt on H/C + n20 car. If I do anything I might get some new appearance mods for a change in pace.

2002 Black SS 6 Speed
Performance Mods: Comp Cam 224/224 .581/.581 112 LSA, TEA Stage 2 5.7L Heads, Comp Dual Springs, Chromemoly Pushrods, Titanium Retainers, Comp High Energy Lifter’s, Ferrea Valves, Ported ARE LS6 Oil Pump, SLP Lid, Mac Headers, 3” True Dual Exhaust with Dynomax Bullet’s, Walbro 255lph Inline and Intank Fuel Pumps, S2 Ported/Polished TB, Moser 12 bolt w/4.11’s, Eaton Posi, 1350 Yoke, T/A Cover, B&M Ripper Shifter, Nitto 275’s
N20 Mods: TNT F1 Kit, MSD Window Switch, NOS Bottle Heater, NGK TR6's
Suspension Mods: BMR Lower Control Arms, Adjustable Panhard Rod, Adjustable Torque Arm, and Custom Subframe Connectors
Misc. Mods: SLP Line Lock, Triple Gauge A Pillar, Harlan Shift Light

411 RWHP 379 RWTQ (http://community.webshots.com/photo/61819781/92816269rEwuzU) (N/A)
532.3 RWHP 649.2 RWTQ (http://community.webshots.com/photo/61819781/92816825gyTXkW) (N20 125 shot)



New Mods: FMS Cam and ASP pulley. New times to come.

[ChevySSGirl]

I'd love to do springs, a 'red' STB - cause I think it would be pretty :) - I'd also like to get my calipers powdercoated red....


:( i need money though - would someone like to start a fund for me?

[coop5885]

ive got my LCA's and PHB that are sitting in my living room right now.
I would like to save up for a 12 bolt, and possiblly N20.

Oh ya, sometime this summer, im thinking about going and getting a 400 crank thats waiting for me to make it a 383, just to be different.

[01SS346]

This summer its a Heads/Cam package and a 12 bolt. This year I did the "got a car mod" and the below listed

[99huggerorangeZ]

bilstien shocks and struts,hotchkis 1" drop springs,hotchkis SFC,rear diff flush and pinion seal replacement,fuel filter replacement
minor shit this year next spring i am gonna be doing headers and cam and maybe even heads:D

[Stew]

17x11 Grand Sports,clutch,Ls6 intake,tuning,control arms,springs,shocks,panhard,bowtie grille.Not much....:D

[MeentSS02]

Well, next weekend I'll be installing my Ground Control coil-over kit with revalved Bilsteins, so I'll finally have it lowered. Beyond that, my goal is to keep it looking as good as possible (which isn't a problem for me), and if I can get a Billingsley 9" rear by the end of this year with a locker, I'll be very happy. Of course, that means a new clutch and driveshaft too :(

If the rear end doesn't happen, I'll be happy with SFCs, changing my plugs and fuel filter, installing my line lock, and running a crapload of top end cleaner through it.

Appearance wise, I'm working on my interior as we speak...I'll be dynamatting the crap outta it soon, the rear seats/seat belts are gone, and I want to make a custom deck to bolt in where the seats were to make it flat.

Should be a fun year!

[Black02SS]

I can't believe you haven't got that kit on yet. Did you get everything taken care of that you needed??

BTW you can say shit on here... :)

[MeentSS02]

SHIT.

Wow, you can. Hmmmmmmmmmmm...I'm too used to that other site.

Man, they messed my order up, and I finally got the right springs in last Friday. I'm having a guy named Travis in PCB install it for me, and since he wasn't available last weekend, I'll be doing it this weekend. I've waited soooo long to lower my stupid car.

[GhstRidr79]

If I get the money I need: Torque converter, cat-back, maybe an h/c package